`Xshell 7 (Build 0115)
Copyright (c) 2020 NetSarang Computer, Inc. All rights reserved.
Connecting to COM11...
Connected.
DDR Version V1.13 20220218
In
ddrconfig:7
LPDDR4X, 324MHz
BW=32 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=4096MB
tdqss: cs0 dqs0: -24ps, dqs1: -120ps, dqs2: -96ps, dqs3: -217ps,
tdqss: cs1 dqs0: -48ps, dqs1: -96ps, dqs2: -96ps, dqs3: -217ps,
change to: 324MHz
PHY drv:clk:36,ca:36,DQ:29,odt:0
vrefinner:24%, vrefout:41%
dram drv:40,odt:0
clk skew:0x64
change to: 528MHz
PHY drv:clk:36,ca:36,DQ:29,odt:0
vrefinner:24%, vrefout:41%
dram drv:40,odt:0
clk skew:0x58
change to: 780MHz
PHY drv:clk:36,ca:36,DQ:29,odt:0
vrefinner:24%, vrefout:41%
dram drv:40,odt:0
clk skew:0x58
change to: 1332MHz(final freq)
PHY drv:clk:36,ca:36,DQ:29,odt:60
vrefinner:16%, vrefout:22%
dram drv:40,odt:80
vref_ca:00000071
clk skew:0x3b
cs 0:
the read training result:
DQS0:0x34, DQS1:0x35, DQS2:0x37, DQS3:0x32,
min : 0xd 0xa 0xf 0xc 0x2 0x4 0x8 0x1 , 0x9 0x8 0x3 0x3 0xf 0xc 0xe 0x8 ,
0x12 0x10 0xd 0xa 0x6 0x2 0x6 0x6 , 0xa 0x7 0x6 0x2 0xf 0xe 0xb 0xf ,
mid :0x26 0x25 0x28 0x25 0x1c 0x1f 0x22 0x1c ,0x22 0x22 0x1b 0x1d 0x29 0x23 0x25 0x21 ,
0x2b 0x2b 0x26 0x24 0x20 0x1d 0x1e 0x20 ,0x23 0x21 0x20 0x1c 0x27 0x27 0x25 0x27 ,
max :0x3f 0x40 0x42 0x3f 0x36 0x3b 0x3d 0x37 ,0x3c 0x3c 0x34 0x37 0x43 0x3b 0x3d 0x3b ,
0x45 0x46 0x3f 0x3f 0x3b 0x38 0x36 0x3b ,0x3d 0x3b 0x3b 0x37 0x40 0x41 0x3f 0x3f ,
range:0x32 0x36 0x33 0x33 0x34 0x37 0x35 0x36 ,0x33 0x34 0x31 0x34 0x34 0x2f 0x2f 0x33 ,
0x33 0x36 0x32 0x35 0x35 0x36 0x30 0x35 ,0x33 0x34 0x35 0x35 0x31 0x33 0x34 0x30 ,
the write training result:
DQS0:0x37, DQS1:0x27, DQS2:0x2b, DQS3:0x17,
min :0x6d 0x70 0x71 0x71 0x63 0x67 0x69 0x6a 0x67 ,0x59 0x59 0x51 0x51 0x5d 0x5c 0x5a 0x5a 0x57 ,
0x62 0x62 0x5c 0x5c 0x55 0x53 0x54 0x59 0x58 ,0x4c 0x4a 0x49 0x45 0x50 0x51 0x4d 0x53 0x49 ,
mid :0x87 0x89 0x8a 0x89 0x7b 0x7f 0x82 0x81 0x7f ,0x72 0x72 0x69 0x69 0x75 0x73 0x73 0x72 0x6e ,
0x7c 0x7c 0x75 0x75 0x6e 0x6b 0x6d 0x72 0x70 ,0x65 0x62 0x60 0x5c 0x69 0x68 0x65 0x6a 0x60 ,
max :0xa1 0xa2 0xa4 0xa1 0x93 0x97 0x9c 0x99 0x97 ,0x8c 0x8b 0x81 0x82 0x8e 0x8a 0x8c 0x8a 0x86 ,
0x96 0x96 0x8e 0x8e 0x87 0x84 0x86 0x8b 0x89 ,0x7e 0x7b 0x78 0x74 0x82 0x80 0x7d 0x82 0x78 ,
range:0x34 0x32 0x33 0x30 0x30 0x30 0x33 0x2f 0x30 ,0x33 0x32 0x30 0x31 0x31 0x2e 0x32 0x30 0x2f ,
0x34 0x34 0x32 0x32 0x32 0x31 0x32 0x32 0x31 ,0x32 0x31 0x2f 0x2f 0x32 0x2f 0x30 0x2f 0x2f ,
cs 1:
the read training result:
DQS0:0x33, DQS1:0x34, DQS2:0x37, DQS3:0x32,
min : 0xa 0xa 0xe 0xb 0x2 0x4 0x8 0x2 , 0x8 0x7 0x2 0x2 0xd 0xa 0xc 0x7 ,
0x12 0x10 0xe 0xa 0x7 0x2 0x6 0x5 , 0xa 0x8 0x7 0x3 0xf 0xe 0xd 0xe ,
mid :0x23 0x24 0x27 0x24 0x1b 0x1e 0x22 0x1c ,0x21 0x21 0x1a 0x1b 0x26 0x21 0x24 0x1f ,
0x2b 0x2a 0x26 0x24 0x20 0x1c 0x1e 0x1f ,0x24 0x21 0x21 0x1d 0x28 0x28 0x26 0x27 ,
max :0x3d 0x3f 0x41 0x3e 0x35 0x38 0x3d 0x37 ,0x3b 0x3b 0x33 0x34 0x40 0x39 0x3c 0x38 ,
0x44 0x45 0x3f 0x3f 0x3a 0x37 0x37 0x39 ,0x3e 0x3b 0x3b 0x37 0x41 0x42 0x3f 0x41 ,
range:0x33 0x35 0x33 0x33 0x33 0x34 0x35 0x35 ,0x33 0x34 0x31 0x32 0x33 0x2f 0x30 0x31 ,
0x32 0x35 0x31 0x35 0x33 0x35 0x31 0x34 ,0x34 0x33 0x34 0x34 0x32 0x34 0x32 0x33 ,
the write training result:
DQS0:0x37, DQS1:0x27, DQS2:0x2b, DQS3:0x17,
min :0x69 0x6a 0x6c 0x6c 0x5e 0x63 0x64 0x64 0x63 ,0x5d 0x5b 0x53 0x54 0x60 0x5d 0x5d 0x5d 0x59 ,
0x5f 0x5e 0x5a 0x59 0x53 0x50 0x51 0x57 0x55 ,0x49 0x48 0x46 0x42 0x4d 0x4e 0x4a 0x50 0x47 ,
mid :0x82 0x84 0x85 0x83 0x76 0x7a 0x7d 0x7c 0x7a ,0x75 0x74 0x6b 0x6c 0x79 0x75 0x75 0x75 0x70 ,
0x79 0x79 0x73 0x73 0x6c 0x69 0x6b 0x70 0x6f ,0x63 0x61 0x5e 0x5b 0x67 0x66 0x63 0x68 0x5f ,
max :0x9b 0x9e 0x9e 0x9b 0x8e 0x92 0x97 0x94 0x92 ,0x8e 0x8d 0x84 0x84 0x92 0x8d 0x8e 0x8d 0x88 ,
0x94 0x94 0x8d 0x8d 0x85 0x83 0x85 0x89 0x89 ,0x7d 0x7b 0x77 0x74 0x81 0x7e 0x7d 0x81 0x78 ,
range:0x32 0x34 0x32 0x2f 0x30 0x2f 0x33 0x30 0x2f ,0x31 0x32 0x31 0x30 0x32 0x30 0x31 0x30 0x2f ,
0x35 0x36 0x33 0x34 0x32 0x33 0x34 0x32 0x34 ,0x34 0x33 0x31 0x32 0x34 0x30 0x33 0x31 0x31 ,
CA Training result:
cs:0 min :0x55 0x3f 0x4e 0x33 0x4e 0x2d 0x4f ,0x53 0x35 0x48 0x2a 0x48 0x28 0x4e ,
cs:0 mid :0x88 0x89 0x7f 0x7e 0x7e 0x7a 0x7a ,0x84 0x81 0x79 0x77 0x76 0x75 0x78 ,
cs:0 max :0xbc 0xd4 0xb1 0xca 0xaf 0xc7 0xa5 ,0xb5 0xce 0xab 0xc5 0xa4 0xc3 0xa3 ,
cs:0 range:0x67 0x95 0x63 0x97 0x61 0x9a 0x56 ,0x62 0x99 0x63 0x9b 0x5c 0x9b 0x55 ,
cs:1 min :0x52 0x4a 0x4a 0x3e 0x49 0x3c 0x4c ,0x4f 0x45 0x46 0x39 0x44 0x37 0x4b ,
cs:1 mid :0x8d 0x8e 0x84 0x82 0x84 0x7f 0x7b ,0x8a 0x87 0x80 0x7d 0x7d 0x7b 0x79 ,
cs:1 max :0xc9 0xd2 0xbf 0xc7 0xc0 0xc3 0xaa ,0xc5 0xca 0xbb 0xc1 0xb7 0xbf 0xa7 ,
cs:1 range:0x77 0x88 0x75 0x89 0x77 0x87 0x5e ,0x76 0x85 0x75 0x88 0x73 0x88 0x5c ,
out
U-Boot SPL board init
U-Boot SPL 2017.09-gaaca6ffec1-211203 #zzz (Dec 03 2021 - 18:42:16)
unknown raw ID phN
unrecognized JEDEC id bytes: 00, 00, 00
Trying to boot from MMC2
MMC error: The cmd index is 1, ret is -110
Card did not respond to voltage select!
mmc_init: -95, time 10
spl: mmc init failed with error: -95
Trying to boot from MMC1
SPL: A/B-slot: _a, successful: 0, tries-remain: 7
Trying fit image at 0x4000 sector
Verified-boot: 0
Checking atf-1 0x00040000 ... sha256(32fbfe6139...) + OK
Checking uboot 0x00a00000 ... sha256(9837d63cd8...) + OK
Checking fdt 0x00b52db8 ... sha256(e8d7718d52...) + OK
Checking atf-2 0xfdcc1000 ... sha256(9662321b37...) + OK
Checking atf-3 0x0006a000 ... sha256(d959b30fef...) + OK
Checking atf-4 0xfdcd0000 ... sha256(b46eaa95b8...) + OK
Checking atf-5 0xfdcce000 ... sha256(2f8839c803...) + OK
Checking atf-6 0x00068000 ... sha256(6e9d32ba23...) + OK
Checking optee 0x08400000 ... sha256(66bbd17352...) + OK
Jumping to U-Boot(0x00a00000) via ARM Trusted Firmware(0x00040000)
Total: 240.513 ms
INFO: Preloader serial: 2
NOTICE: BL31: v2.3():v2.3-389-g4613ae965:cl
NOTICE: BL31: Built : 11:21:14, Jul 7 2022
INFO: GICv3 without legacy support detected.
INFO: ARM GICv3 driver initialized in EL3
INFO: pmu v1 is valid 220114
INFO: dfs DDR fsp_param[0].freq_mhz= 1332MHz
INFO: dfs DDR fsp_param[1].freq_mhz= 324MHz
INFO: dfs DDR fsp_param[2].freq_mhz= 528MHz
INFO: dfs DDR fsp_param[3].freq_mhz= 780MHz
INFO: Using opteed sec cpu_context!
INFO: boot cpu mask: 0
INFO: BL31: Initializing runtime services
INFO: BL31: Initializing BL32
I/TC:
I/TC: OP-TEE version: 3.13.0-641-g4167319d3 #hisping.lin (gcc version 10.2.1 20201103 (GNU Toolchain for the A-profile Architecture 10.2-2020.11 (arm-10.16))) #8 Wed Mar 16 15:14:56 CST 2022 aarch64
I/TC: Primary CPU initializing
I/TC: Primary CPU switching to normal world boot
INFO: BL31: Preparing for EL3 exit to normal world
INFO: Entry point address = 0xa00000
INFO: SPSR = 0x3c9
U-Boot 2017.09(u-boot commit id: 642a3d254a444f95f47046e38407fdc35e418ebc)(sdk version: )-g642a3d254a-dirty #jenkins (Sep 05 2022 - 16:34:55 +0800), Build: jenkins-rk3568-photonicat-openwrt-old-1
Model: Rockchip RK3568 Evaluation Board
PreSerial: 2, raw, 0xfe660000
DRAM: 4 GiB
Sysmem: init
Relocation Offset: ed326000
Relocation fdt: eb9f8a80 - eb9fecc8
CR: M/C/I
Using default environment
dwmmc@fe2b0000: 1, dwmmc@fe2c0000: 2, sdhci@fe310000: 0
Bootdev(atags): mmc 0
MMC0: HS200, 200Mhz
PartType: EFI
DM: v1
boot mode: None
FIT: no signed, no conf required
DTB: rk-kernel.dtb
HASH(c): OK
NODE=net-led, LABEL=000000000a115704
NODE=work-led, LABEL=000000000a115754
I2c0 speed: 100000Hz
vdd_cpu init 900000 uV
vdd_logic init 900000 uV
vdd_npu init 950000 uV
io-domain: OK
Could not find baseparameter partition
Model: Rockchip RK3568 photonicat Linux Board
Rockchip UBOOT DRM driver version: v1.0.1
VOP have 1 active VP
vp0 have layer nr:6[0 2 4 1 3 5 ], primary plane: 4
vp1 have layer nr:0[], primary plane: 0
vp2 have layer nr:0[], primary plane: 0
hdmi@fe0a0000 disconnected
CLK: (sync kernel. arm: enter 816000 KHz, init 816000 KHz, kernel 0N/A)
apll 1416000 KHz
dpll 666000 KHz
gpll 1188000 KHz
cpll 1000000 KHz
npll 1200000 KHz
vpll 24000 KHz
hpll 24000 KHz
ppll 200000 KHz
armclk 1416000 KHz
aclk_bus 150000 KHz
pclk_bus 100000 KHz
aclk_top_high 500000 KHz
aclk_top_low 400000 KHz
hclk_top 150000 KHz
pclk_top 100000 KHz
aclk_perimid 300000 KHz
hclk_perimid 150000 KHz
pclk_pmu 100000 KHz
Net: eth1: ethernet@fe010000
Hit key to stop autoboot('CTRL+C'): 0
gpio: pin 014 (gpio 14) value is 0
Card did not respond to voltage select!
mmc_init: -95, time 9
Booting FIT Image at 0xea783240 with size 0x01074800
Fdt Ramdisk skip relocation
Loading kernel from FIT Image at ea783240 ...
Using 'conf' configuration
optee api revision: 2.0
TEEC: Waring: Could not find security partition
Verified-boot: 0
Trying 'kernel' kernel subimage
Description: unavailable
Type: Kernel Image
Compression: uncompressed
Data Start: 0xea7a0040
Data Size: 17135624 Bytes = 16.3 MiB
Architecture: AArch64
OS: Linux
Load Address: 0x00280000
Entry Point: 0x00280000
Hash algo: sha256
Hash value: 3843e5947705d43f7e6a5a996e1e1f989a0433f021e6016916f33edab0a7f018
Verifying Hash Integrity ... sha256+ OK
Loading fdt from FIT Image at ea783240 ...
Using 'conf' configuration
Trying 'fdt' fdt subimage
Description: unavailable
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0xea783a40
Data Size: 116182 Bytes = 113.5 KiB
Architecture: AArch64
Load Address: 0x0a100000
Hash algo: sha256
Hash value: b907e4c5bfd50d5e5c2dab2f84e5599b7b777be0a627da3e82b71c64eee69f07
Verifying Hash Integrity ... sha256+ OK
Loading fdt from 0x0a100000 to 0x0a100000
Booting using the fdt blob at 0x0a100000
Loading Kernel Image from 0xea7a0040 to 0x00280000 ... OK
kernel loaded at 0x00280000, end = 0x012d7808
'reserved-memory' ramoops@110000: addr=110000 size=f0000
'reserved-memory' dma_trans@3c000000: addr=3c000000 size=4000000
Using Device Tree in place at 000000000a100000, end 000000000a11f5d5
vp0, plane_mask:0x3f, primary-id:4, curser-id:-1
vp1, plane_mask:0x0, primary-id:0, curser-id:-1
vp2, plane_mask:0x0, primary-id:0, curser-id:-1
Adding bank: 0x00200000 - 0x08400000 (size: 0x08200000)
Adding bank: 0x09400000 - 0xf0000000 (size: 0xe6c00000)
Adding bank: 0x1f0000000 - 0x200000000 (size: 0x10000000)
Total: 3558.825 ms
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x412fd050]
[ 0.000000] Linux version 4.19.232-photonicat (jenkins@hpbuild) (develop-4.19: bc492cee84a31535ec5b1ba4152bf5071ba37bb1) (sdk version🙂 (gcc version 6.3.1 20170404 (Linaro GCC 6.3-2017.05), GNU ld (Linaro_Binutils-2017.05) 2.27.0.20161019) #1 SMP Mon Sep 5 16:35:04 CST 2022
[ 0.000000] Machine model: Rockchip RK3568 photonicat Linux Board
[ 0.000000] earlycon: uart8250 at MMIO32 0x00000000fe660000 (options '')
[ 0.000000] bootconsole [uart8250] enabled
[ 0.000000] cma: Reserved 16 MiB at 0x00000000eec00000
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.1 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: Trusted OS migration not required
[ 0.000000] psci: SMC Calling Convention v1.2
[ 0.000000] percpu: Embedded 24 pages/cpu s57704 r8192 d32408 u98304
[ 0.000000] Detected VIPT I-cache on CPU0
[ 0.000000] CPU features: detected: Virtualization Host Extensions
[ 0.000000] CPU features: detected: Speculative Store Bypassing Safe (SSBS)
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 1027656
[ 0.000000] Kernel command line: storagemedia=emmc androidboot.storagemedia=emmc androidboot.mode=normal storagenode=/sdhci@fe310000 root=/dev/mmcblk0p6 rootwait earlycon=uart8250,mmio32,0xfe660000 console=ttyFIQ0 rootfstype=squashfs coherent_pool=1m systemd.gpt_auto=0 cgroup_enable=memory swapaccount=1 consoleblank=0 video=HDMI-A-1:e
[ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] software IO TLB: mapped [mem 0xe9f00000-0xedf00000] (64MB)
[ 0.000000] Memory: 3908664K/4175872K available (10494K kernel code, 1438K rwdata, 3388K rodata, 1344K init, 506K bss, 250824K reserved, 16384K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] ftrace: allocating 38775 entries in 152 pages
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: RCU event tracing is enabled.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode
[ 0.000000] GICv3: Distributor has no Range Selector support
[ 0.000000] GICv3: no VLPI support, no direct LPI support
[ 0.000000] ITS [mem 0xfd440000-0xfd45ffff]
[ 0.000000] ITS@0x00000000fd440000: allocated 8192 Devices @210000 (indirect, esz 8, psz 64K, shr 0)
[ 0.000000] ITS@0x00000000fd440000: allocated 32768 Interrupt Collections @220000 (flat, esz 2, psz 64K, shr 0)
[ 0.000000] ITS: using cache flushing for cmd queue
[ 0.000000] GIC: using LPI property table @0x0000000000230000
[ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x00000000fd460000
[ 0.000000] CPU0: using LPI pending table @0x0000000000240000
[ 0.000000] GIC: using cache flushing for LPI property table
[ 0.000000] random: random: get_random_bytes called from start_kernel+0x36c/0x510 with crng_init=0
[ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[ 0.000004] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[ 0.001596] Console: colour dummy device 80x25
[ 0.002040] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=80000)
[ 0.002987] pid_max: default: 32768 minimum: 301
[ 0.003525] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.004155] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.006024] ASID allocator initialised with 32768 entries
[ 0.006628] rcu: Hierarchical SRCU implementation.
[ 0.008525] Platform MSI: interrupt-controller@fd440000 domain created
[ 0.009461] PCI/MSI: /interrupt-controller@fd400000/interrupt-controller@fd440000 domain created
[ 0.010773] smp: Bringing up secondary CPUs ...
I/TC: Secondary CPU 1 initializing
I/TC: Secondary CPU 1 switching to normal world boot
I/TC: Secondary CPU 2 initializing
I/TC: Secondary CPU 2 switching to normal world boot
I/TC: Secondary CPU 3 initializing
I/TC: Secondary CPU 3 switching to normal world boot
[ 0.012435] Detected VIPT I-cache on CPU1
[ 0.012464] GICv3: CPU1: found redistributor 100 region 0:0x00000000fd480000
[ 0.012501] CPU1: using LPI pending table @0x0000000000250000
[ 0.012546] CPU1: Booted secondary processor 0x0000000100 [0x412fd050]
[ 0.013807] Detected VIPT I-cache on CPU2
[ 0.013829] GICv3: CPU2: found redistributor 200 region 0:0x00000000fd4a0000
[ 0.013864] CPU2: using LPI pending table @0x0000000000260000
[ 0.013899] CPU2: Booted secondary processor 0x0000000200 [0x412fd050]
[ 0.015116] Detected VIPT I-cache on CPU3
[ 0.015136] GICv3: CPU3: found redistributor 300 region 0:0x00000000fd4c0000
[ 0.015170] CPU3: using LPI pending table @0x0000000000270000
[ 0.015201] CPU3: Booted secondary processor 0x0000000300 [0x412fd050]
[ 0.015285] smp: Brought up 1 node, 4 CPUs
[ 0.022071] SMP: Total of 4 processors activated.
[ 0.022508] CPU features: detected: GIC system register CPU interface
[ 0.023095] CPU features: detected: Privileged Access Never
[ 0.023603] CPU features: detected: LSE atomic instructions
[ 0.024116] CPU features: detected: User Access Override
[ 0.024604] CPU features: detected: 32-bit EL0 Support
[ 0.025076] CPU features: detected: RAS Extension Support
[ 0.025701] CPU: All CPU(s) started at EL2
[ 0.026098] alternatives: patching kernel code
[ 0.030253] devtmpfs: initialized
[ 0.045968] Registered cp15_barrier emulation handler
[ 0.046470] Registered setend emulation handler
[ 0.047116] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370867519511994 ns
[ 0.048017] futex hash table entries: 1024 (order: 4, 65536 bytes)
[ 0.049074] pinctrl core: initialized pinctrl subsystem
[ 0.050345] NET: Registered protocol family 16
[ 0.053319] cpuidle: using governor menu
[ 0.053708] Registered FIQ tty driver
[ 0.054395] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 0.055931] DMA: preallocated 1024 KiB pool for atomic allocations
[ 0.059071] console [pstore-1] enabled
[ 0.059421] pstore: Registered ramoops as persistent store backend
[ 0.060027] ramoops: attached 0xf0000@0x110000, ecc: 0/0
[ 0.083733] GPIO line 14 (sd-pwren) hogged as output/high
[ 0.084501] rockchip-gpio fdd60000.gpio: probed gpio0 (fdd60000.gpio)
[ 0.085535] rockchip-gpio fe740000.gpio: probed gpio1 (fe740000.gpio)
[ 0.086388] GPIO line 73 (wlan-reg-en) hogged as output/high
[ 0.087117] rockchip-gpio fe750000.gpio: probed gpio2 (fe750000.gpio)
[ 0.088129] rockchip-gpio fe760000.gpio: probed gpio3 (fe760000.gpio)
[ 0.088984] GPIO line 154 (aux-pwren) hogged as output/high
[ 0.089681] rockchip-gpio fe770000.gpio: probed gpio4 (fe770000.gpio)
[ 0.090370] rockchip-pinctrl pinctrl: probed pinctrl
[ 0.096888] cryptd: max_cpu_qlen set to 1000
[[ 0.098619] console [ttyFIQ0] enabled
0.098619] console [ttyFIQ0] enabled
[ 0.099292] bootconsole [uart8250] disabled
[ 0.099292] bootconsole [uart8250] disabled
[ 0.099874] Registered fiq debugger ttyFIQ0
[ 0.100557] vcc3v3_sys: supplied by dc_5v
[ 0.100855] vcc5v0_sys: supplied by dc_5v
[ 0.101480] vcc_1v8: supplied by vcc5v0_sys
[ 0.101775] vcc_3v3: supplied by vcc5v0_sys
[ 0.102069] vdd_fixed: supplied by vcc5v0_sys
[ 0.102363] vcc2v5-sys: supplied by vcc3v3_sys
[ 0.102660] pcie30_avdd0v9: supplied by vcc3v3_sys
[ 0.102955] pcie30_avdd1v8: supplied by vcc3v3_sys
[ 0.103283] vcc3v3_bu: supplied by vcc5v0_sys
[ 0.104496] rk_iommu fdea0800.iommu: version = 2
[ 0.104948] rk_iommu fded0480.iommu: version = 2
[ 0.105432] rk_iommu fdee0800.iommu: version = 2
[ 0.105741] rk_iommu fdef0800.iommu: version = 2
[ 0.106020] rk_iommu fdf40f00.iommu: version = 2
[ 0.106371] rk_iommu fdf80800.iommu: version = 2
[ 0.106627] rk_iommu fe043e00.iommu: version = 2
[ 0.107362] SCSI subsystem initialized
[ 0.107536] usbcore: registered new interface driver usbfs
[ 0.107586] usbcore: registered new interface driver hub
[ 0.107633] usbcore: registered new device driver usb
[ 0.107762] pps_core: LinuxPPS API ver. 1 registered
[ 0.107777] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti giometti@linux.it
[ 0.107806] PTP clock support registered
[ 0.108071] arm-scmi firmware:scmi: SCMI Protocol v2.0 'rockchip:' Firmware version 0x0
[ 0.109916] Advanced Linux Sound Architecture Driver Initialized.
[ 0.111781] rockchip-cpuinfo cpuinfo: SoC : 35682000
[ 0.111814] rockchip-cpuinfo cpuinfo: Serial : 93ce78bf3e7bc147
[ 0.112636] clocksource: Switched to clocksource arch_sys_counter
[ 0.149712] VFS: Disk quotas dquot_6.6.0
[ 0.149811] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.158027] thermal thermal_zone1: power_allocator: sustainable_power will be estimated
[ 0.158309] NET: Registered protocol family 2
[ 0.158500] IP idents hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.159936] tcp_listen_portaddr_hash hash table entries: 2048 (order: 4, 81920 bytes)
[ 0.160020] TCP established hash table entries: 32768 (order: 6, 262144 bytes)
[ 0.160212] TCP bind hash table entries: 32768 (order: 8, 1048576 bytes)
[ 0.160933] TCP: Hash tables configured (established 32768 bind 32768)
[ 0.161057] UDP hash table entries: 2048 (order: 5, 196608 bytes)
[ 0.161231] UDP-Lite hash table entries: 2048 (order: 5, 196608 bytes)
[ 0.161502] NET: Registered protocol family 1
[ 0.163333] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available
[ 0.163806] kvm [1]: 16-bit VMID
[ 0.163833] kvm [1]: GICv3: no GICV resource entry
[ 0.163847] kvm [1]: disabling GICv2 emulation
[ 0.163854] kvm [1]: GIC system register CPU interface enabled
[ 0.163966] kvm [1]: vgic interrupt IRQ1
[ 0.164099] kvm [1]: VHE mode initialized successfully
[ 0.165784] Initialise system trusted keyrings
[ 0.165944] workingset: timestamp_bits=61 max_order=20 bucket_order=0
[ 0.171569] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.171732] jffs2: version 2.2. (NAND) (SUMMARY) ? 2001-2006 Red Hat, Inc.
[ 0.171959] fuse init (API version 7.27)
[ 0.174208] NET: Registered protocol family 38
[ 0.174249] Key type asymmetric registered
[ 0.174259] Asymmetric key parser 'x509' registered
[ 0.174293] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 243)
[ 0.174310] io scheduler noop registered
[ 0.174323] io scheduler deadline registered
[ 0.174428] io scheduler cfq registered (default)
[ 0.174445] io scheduler mq-deadline registered
[ 0.174458] io scheduler kyber registered
[ 0.176713] phy phy-fe8a0000.usb2-phy.0: Linked as a consumer to regulator.4
[ 0.176851] phy phy-fe8a0000.usb2-phy.1: Linked as a consumer to regulator.4
[ 0.176964] phy phy-fe8a0000.usb2-phy.1: No vbus specified for otg port
[ 0.178114] extcon extcon1: failed to create extcon usb2-phy link
[ 0.178228] phy phy-fe8b0000.usb2-phy.2: Linked as a consumer to regulator.4
[ 0.178383] phy phy-fe8b0000.usb2-phy.3: Linked as a consumer to regulator.4
[ 0.178492] phy phy-fe8b0000.usb2-phy.3: No vbus specified for otg port
[ 0.185026] rk-pcie 3c0800000.pcie: Linked as a consumer to regulator.12
[ 0.188740] dma-pl330 fe530000.dmac: Loaded driver for PL330 DMAC-241330
[ 0.188783] dma-pl330 fe530000.dmac: DBUFF-128x8bytes Num_Chans-8 Num_Peri-32 Num_Events-16
[ 0.190799] dma-pl330 fe550000.dmac: Loaded driver for PL330 DMAC-241330
[ 0.190824] dma-pl330 fe550000.dmac: DBUFF-128x8bytes Num_Chans-8 Num_Peri-32 Num_Events-16
[ 0.191890] rockchip-system-monitor rockchip-system-monitor: system monitor probe
[ 0.192464] vdd_logic: supplied by vcc5v0_sys
[ 0.192894] vdd_npu: supplied by vcc5v0_sys
[ 0.193542] Serial: 8250/16550 driver, 10 ports, IRQ sharing disabled
[ 0.194312] fe650000.serial: ttyS1 at MMIO 0xfe650000 (irq = 59, base_baud = 1500000) is a 16550A
[ 0.194759] fe670000.serial: ttyS3 at MMIO 0xfe670000 (irq = 60, base_baud = 1500000) is a 16550A
[ 0.195137] fe680000.serial: ttyS4 at MMIO 0xfe680000 (irq = 61, base_baud = 1500000) is a 16550A
[ 0.195537] fe6d0000.serial: ttyS9 at MMIO 0xfe6d0000 (irq = 62, base_baud = 1500000) is a 16550A
[ 0.197318] rk-pcie 3c0800000.pcie: missing legacy IRQ resource
[ 0.197351] rk-pcie 3c0800000.pcie: Missing config reg space
[ 0.197371] rk-pcie 3c0800000.pcie: host bridge /pcie@fe280000 ranges:
[ 0.197400] rk-pcie 3c0800000.pcie: err 0xf0000000..0xf00fffff -> 0xf0000000
[ 0.197426] rk-pcie 3c0800000.pcie: IO 0xf0100000..0xf01fffff -> 0xf0100000
[ 0.197452] rk-pcie 3c0800000.pcie: MEM 0xf0200000..0xf1ffffff -> 0xf0200000
[ 0.197472] rk-pcie 3c0800000.pcie: MEM 0x380000000..0x3bfffffff -> 0x380000000
[ 0.197858] random: fast init done
[ 0.198151] random: crng init done
[ 0.198167] iommu: Adding device fe040000.vop to group 6
[ 0.198204] rockchip-vop2 fe040000.vop: Linked as a consumer to fe043e00.iommu
[ 0.201744] rockchip-drm display-subsystem: Linked as a consumer to fe040000.vop
[ 0.202651] rockchip-drm display-subsystem: Linked as a consumer to fe0a0000.hdmi
[ 0.204084] rockchip-drm display-subsystem: defer getting devfreq
[ 0.204328] vp0: rgb_pixelclk: 0
[ 0.204359] rockchip-vop2 fe040000.vop: [drm:vop2_bind] vp0 assign plane mask: 0x3f, primary plane phy id: 4
[ 0.204376] vp1: rgb_pixelclk: 0
[ 0.204391] rockchip-vop2 fe040000.vop: [drm:vop2_bind] vp1 assign plane mask: 0x0, primary plane phy id: -1
[ 0.204402] vp2: rgb_pixelclk: 0
[ 0.204414] rockchip-vop2 fe040000.vop: [drm:vop2_bind] vp2 assign plane mask: 0x0, primary plane phy id: -1
[ 0.204585] [drm] failed to init overlay plane Cluster0-win0
[ 0.204601] [drm] failed to init overlay plane Cluster0-win1
[ 0.204612] [drm] failed to init overlay plane Cluster1-win0
[ 0.204625] [drm] failed to init overlay plane Cluster1-win1
[ 0.204710] rockchip-drm display-subsystem: bound fe040000.vop (ops 0xffffff8008b725b0)
[ 0.204898] dwhdmi-rockchip fe0a0000.hdmi: Detected HDMI TX controller v2.11a with HDCP (DWC HDMI 2.0 TX PHY)
[ 0.205441] dwhdmi-rockchip fe0a0000.hdmi: registered DesignWare HDMI I2C bus driver
[ 0.205916] [drm] forcing HDMI-A-1 connector on
[ 0.206015] rockchip-drm display-subsystem: bound fe0a0000.hdmi (ops 0xffffff8008b760c8)
[ 0.206036] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 0.206049] [drm] No driver support for vblank timestamp query.
[ 0.207023] dwhdmi-rockchip fe0a0000.hdmi: failed to get edid
[ 0.207091] rockchip-drm display-subsystem: can't not find any loader display
[ 0.207111] rockchip-drm display-subsystem: failed to show loader logo
[ 0.207860] dwhdmi-rockchip fe0a0000.hdmi: failed to get edid
[ 0.212599] dwhdmi-rockchip fe0a0000.hdmi: failed to get edid
[ 0.213423] rockchip-vop2 fe040000.vop: [drm:vop2_crtc_atomic_enable] Update mode to 1280x720p60, type: 11 for vp0
[ 0.273091] Console: switching to colour frame buffer device 160x45
[ 0.289097] rockchip-drm display-subsystem: fb0: frame buffer device
[ 0.289876] [drm] Initialized rockchip 2.0.0 20140818 for display-subsystem on minor 0
[ 0.295080] cacheinfo: Unable to detect cache hierarchy for CPU 0
[ 0.295709] brd: module loaded
[ 0.301601] loop: module loaded
[ 0.302006] zram: Added device: zram0
[ 0.302120] lkdtm: No crash points registered, enable through debugfs
[ 0.304000] Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)
[ 0.307219] rk_gmac-dwmac fe010000.ethernet: no regulator found
[ 0.307252] rk_gmac-dwmac fe010000.ethernet: clock input or output? (output).
[ 0.307264] rk_gmac-dwmac fe010000.ethernet: TX delay(0x30).
[ 0.307273] rk_gmac-dwmac fe010000.ethernet: RX delay(0x10).
[ 0.307287] rk_gmac-dwmac fe010000.ethernet: integrated PHY? (no).
[ 0.312343] rk_gmac-dwmac fe010000.ethernet: init for RGMII
[ 0.312570] rk_gmac-dwmac fe010000.ethernet: User ID: 0x30, Synopsys ID: 0x51
[ 0.312589] rk_gmac-dwmac fe010000.ethernet: DWMAC4/5
[ 0.312606] rk_gmac-dwmac fe010000.ethernet: DMA HW capability register supported
[ 0.312619] rk_gmac-dwmac fe010000.ethernet: RX Checksum Offload Engine supported
[ 0.312647] rk_gmac-dwmac fe010000.ethernet: TX Checksum insertion supported
[ 0.312663] rk_gmac-dwmac fe010000.ethernet: Wake-Up On Lan supported
[ 0.312705] rk_gmac-dwmac fe010000.ethernet: TSO supported
[ 0.312720] rk_gmac-dwmac fe010000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[ 0.312735] rk_gmac-dwmac fe010000.ethernet: TSO feature enabled
[ 0.446616] YT8521 Ethernet stmmac-1:00: [phy_probe-1931] led_status_value normal
[ 0.447600] rk_gmac-dwmac fe2a0000.ethernet: no regulator found
[ 0.447624] rk_gmac-dwmac fe2a0000.ethernet: Can not read property: clock_in_out.
[ 0.447635] rk_gmac-dwmac fe2a0000.ethernet: Can not read property: tx_delay.
[ 0.447643] rk_gmac-dwmac fe2a0000.ethernet: set tx_delay to 0xffffffff
[ 0.447652] rk_gmac-dwmac fe2a0000.ethernet: Can not read property: rx_delay.
[ 0.447660] rk_gmac-dwmac fe2a0000.ethernet: set rx_delay to 0xffffffff
[ 0.447787] rk_gmac-dwmac fe2a0000.ethernet: integrated PHY? (no).
[ 0.447850] rk_gmac-dwmac fe2a0000.ethernet: clock input from PHY
[ 0.452874] rk_gmac-dwmac fe2a0000.ethernet: init for SGMII
[ 0.509542] rk_gmac-dwmac fe2a0000.ethernet: User ID: 0x30, Synopsys ID: 0x51
[ 0.509564] rk_gmac-dwmac fe2a0000.ethernet: DWMAC4/5
[ 0.509576] rk_gmac-dwmac fe2a0000.ethernet: DMA HW capability register supported
[ 0.509585] rk_gmac-dwmac fe2a0000.ethernet: RX Checksum Offload Engine supported
[ 0.509592] rk_gmac-dwmac fe2a0000.ethernet: TX Checksum insertion supported
[ 0.509600] rk_gmac-dwmac fe2a0000.ethernet: Wake-Up On Lan supported
[ 0.509635] rk_gmac-dwmac fe2a0000.ethernet: TSO supported
[ 0.509651] rk_gmac-dwmac fe2a0000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[ 0.509666] rk_gmac-dwmac fe2a0000.ethernet: TSO feature enabled
[ 0.643267] YT8521 Ethernet stmmac-0:00: [phy_probe-1931] led_status_value normal
[ 0.645521] dwc3 fcc00000.dwc3: Failed to get clk 'ref': -2
[ 0.648771] dwc3 fd000000.dwc3: Failed to get clk 'ref': -2
[ 0.652868] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.652904] ehci-pci: EHCI PCI platform driver
[ 0.652964] ehci-platform: EHCI generic platform driver
[ 0.655211] ehci-platform fd800000.usb: EHCI Host Controller
[ 0.655245] ehci-platform fd800000.usb: new USB bus registered, assigned bus number 1
[ 0.655530] ehci-platform fd800000.usb: irq 11, io mem 0xfd800000
[ 0.665994] ehci-platform fd800000.usb: USB 2.0 started, EHCI 1.00
[ 0.666213] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19
[ 0.666232] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.666255] usb usb1: Product: EHCI Host Controller
[ 0.666268] usb usb1: Manufacturer: Linux 4.19.232-photonicat ehci_hcd
[ 0.666280] usb usb1: SerialNumber: fd800000.usb
[ 0.666735] hub 1-0:1.0: USB hub found
[ 0.666781] hub 1-0:1.0: 1 port detected
[ 0.669316] ehci-platform fd880000.usb: EHCI Host Controller
[ 0.669348] ehci-platform fd880000.usb: new USB bus registered, assigned bus number 2
[ 0.669627] ehci-platform fd880000.usb: irq 13, io mem 0xfd880000
[ 0.682663] ehci-platform fd880000.usb: USB 2.0 started, EHCI 1.00
[ 0.682860] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19
[ 0.682878] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.682899] usb usb2: Product: EHCI Host Controller
[ 0.682912] usb usb2: Manufacturer: Linux 4.19.232-photonicat ehci_hcd
[ 0.682924] usb usb2: SerialNumber: fd880000.usb
[ 0.683325] hub 2-0:1.0: USB hub found
[ 0.683367] hub 2-0:1.0: 1 port detected
[ 0.684054] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 0.684084] ohci-platform: OHCI generic platform driver
[ 0.684315] ohci-platform fd840000.usb: Generic Platform OHCI controller
[ 0.684348] ohci-platform fd840000.usb: new USB bus registered, assigned bus number 3
[ 0.684525] ohci-platform fd840000.usb: irq 12, io mem 0xfd840000
[ 0.743477] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 4.19
[ 0.743497] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.743507] usb usb3: Product: Generic Platform OHCI controller
[ 0.743515] usb usb3: Manufacturer: Linux 4.19.232-photonicat ohci_hcd
[ 0.743523] usb usb3: SerialNumber: fd840000.usb
[ 0.743938] hub 3-0:1.0: USB hub found
[ 0.743986] hub 3-0:1.0: 1 port detected
[ 0.744460] ohci-platform fd8c0000.usb: Generic Platform OHCI controller
[ 0.744493] ohci-platform fd8c0000.usb: new USB bus registered, assigned bus number 4
[ 0.744685] ohci-platform fd8c0000.usb: irq 14, io mem 0xfd8c0000
[ 0.803483] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 4.19
[ 0.803502] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.803512] usb usb4: Product: Generic Platform OHCI controller
[ 0.803520] usb usb4: Manufacturer: Linux 4.19.232-photonicat ohci_hcd
[ 0.803528] usb usb4: SerialNumber: fd8c0000.usb
[ 0.803935] hub 4-0:1.0: USB hub found
[ 0.803980] hub 4-0:1.0: 1 port detected
[ 0.805380] xhci-hcd xhci-hcd.4.auto: xHCI Host Controller
[ 0.805417] xhci-hcd xhci-hcd.4.auto: new USB bus registered, assigned bus number 5
[ 0.805898] xhci-hcd xhci-hcd.4.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x0000011002010010
[ 0.805981] xhci-hcd xhci-hcd.4.auto: irq 76, io mem 0xfcc00000
[ 0.806269] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19
[ 0.806288] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.806302] usb usb5: Product: xHCI Host Controller
[ 0.806315] usb usb5: Manufacturer: Linux 4.19.232-photonicat xhci-hcd
[ 0.806327] usb usb5: SerialNumber: xhci-hcd.4.auto
[ 0.806740] hub 5-0:1.0: USB hub found
[ 0.806791] hub 5-0:1.0: 1 port detected
[ 0.807108] xhci-hcd xhci-hcd.4.auto: xHCI Host Controller
[ 0.807135] xhci-hcd xhci-hcd.4.auto: new USB bus registered, assigned bus number 6
[ 0.807158] xhci-hcd xhci-hcd.4.auto: Host supports USB 3.0 SuperSpeed
[ 0.807232] usb usb6: We don't know the algorithms for LPM for this host, disabling LPM.
[ 0.807355] usb usb6: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 4.19
[ 0.807373] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.807388] usb usb6: Product: xHCI Host Controller
[ 0.807400] usb usb6: Manufacturer: Linux 4.19.232-photonicat xhci-hcd
[ 0.807413] usb usb6: SerialNumber: xhci-hcd.4.auto
[ 0.807811] hub 6-0:1.0: USB hub found
[ 0.807858] hub 6-0:1.0: 1 port detected
[ 0.808324] xhci-hcd xhci-hcd.5.auto: xHCI Host Controller
[ 0.808357] xhci-hcd xhci-hcd.5.auto: new USB bus registered, assigned bus number 7
[ 0.808824] xhci-hcd xhci-hcd.5.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x0000011002010010
[ 0.808881] xhci-hcd xhci-hcd.5.auto: irq 77, io mem 0xfd000000
[ 0.809155] usb usb7: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19
[ 0.809175] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.809190] usb usb7: Product: xHCI Host Controller
[ 0.809202] usb usb7: Manufacturer: Linux 4.19.232-photonicat xhci-hcd
[ 0.809214] usb usb7: SerialNumber: xhci-hcd.5.auto
[ 0.809650] hub 7-0:1.0: USB hub found
[ 0.809695] hub 7-0:1.0: 1 port detected
[ 0.810009] xhci-hcd xhci-hcd.5.auto: xHCI Host Controller
[ 0.810035] xhci-hcd xhci-hcd.5.auto: new USB bus registered, assigned bus number 8
[ 0.810058] xhci-hcd xhci-hcd.5.auto: Host supports USB 3.0 SuperSpeed
[ 0.810137] usb usb8: We don't know the algorithms for LPM for this host, disabling LPM.
[ 0.810259] usb usb8: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 4.19
[ 0.810276] usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.810290] usb usb8: Product: xHCI Host Controller
[ 0.810303] usb usb8: Manufacturer: Linux 4.19.232-photonicat xhci-hcd
[ 0.810314] usb usb8: SerialNumber: xhci-hcd.5.auto
[ 0.810697] hub 8-0:1.0: USB hub found
[ 0.810744] hub 8-0:1.0: 1 port detected
[ 0.811148] usbcore: registered new interface driver cdc_wdm
[ 0.811379] usbcore: registered new interface driver uas
[ 0.811533] usbcore: registered new interface driver usb-storage
[ 0.812729] usbcore: registered new interface driver usbtouchscreen
[ 0.812794] cyttsp5_loader_init: Parade TTSP FW Loader Driver (Built TTDA.03.08.874312) rc=0
[ 0.812812] cyttsp5_device_access_init: Parade TTSP Device Access Driver (Built TTDA.03.08.874312) rc=0
[ 0.813158] .. rk pwm remotectl v2.0 init
[ 0.813446] input: fe700030.pwm as /devices/platform/fe700030.pwm/input/input0
[ 0.813784] remotectl-pwm fe700030.pwm: pwm version is 0x2130000
[ 0.813844] remotectl-pwm fe700030.pwm: Controller support pwrkey capture
[ 0.814384] i2c /dev entries driver
[ 0.816275] fan53555-regulator 0-001c: FAN53555 Option[12] Rev[15] Detected!
[ 0.818056] vdd_cpu: supplied by vcc5v0_sys
[ 0.821499] rockchip-pinctrl pinctrl: pin gpio1-1 already requested by fe670000.serial; cannot claim for fe5c0000.i2c
[ 0.821523] rockchip-pinctrl pinctrl: pin-33 (fe5c0000.i2c) status -22
[ 0.821539] rockchip-pinctrl pinctrl: could not request pin 33 (gpio1-1) from group i2c3m0-xfer on device rockchip-pinctrl
[ 0.821553] rk3x-i2c fe5c0000.i2c: Error applying setting, reverse things back
[ 0.821577] rk3x-i2c: probe of fe5c0000.i2c failed with error -22
[ 0.822788] rockchip-iodomain fdc20000.syscon:io-domains: Linked as a consumer to regulator.6
[ 0.822816] rockchip-iodomain fdc20000.syscon:io-domains: pmuio1(3300000 uV) supplied by vcc_3v3
[ 0.822906] rockchip-iodomain fdc20000.syscon:io-domains: pmuio2(3300000 uV) supplied by vcc_3v3
[ 0.822994] rockchip-iodomain fdc20000.syscon:io-domains: vccio1(3300000 uV) supplied by vcc_3v3
[ 0.823101] rockchip-iodomain fdc20000.syscon:io-domains: vccio3(3300000 uV) supplied by vcc_3v3
[ 0.823196] rockchip-iodomain fdc20000.syscon:io-domains: vccio4(3300000 uV) supplied by vcc_3v3
[ 0.823285] rockchip-iodomain fdc20000.syscon:io-domains: vccio5(3300000 uV) supplied by vcc_3v3
[ 0.823361] rockchip-iodomain fdc20000.syscon:io-domains: vccio6(3300000 uV) supplied by vcc_3v3
[ 0.823453] rockchip-iodomain fdc20000.syscon:io-domains: vccio7(3300000 uV) supplied by vcc_3v3
[ 0.826206] rockchip-thermal fe710000.tsadc: tsadc is probed successfully!
[ 0.827353] cpu cpu0: leakage=34
[ 0.827404] cpu cpu0: pvtm = 88520, from nvmem
[ 0.827429] cpu cpu0: pvtm-volt-sel=1
[ 0.827733] cpu cpu0: Linked as a consumer to regulator.15
[ 0.827792] cpu cpu0: Dropping the link to regulator.15
[ 0.827948] cpu cpu0: Linked as a consumer to regulator.15
[ 0.828573] cpu cpu0: avs=0
[ 0.828634] energy_model: pd0: hertz/watts ratio non-monotonically decreasing: em_cap_state 2 >= em_cap_state1
[ 0.828819] cpu cpu0: l=0 h=2147483647 hyst=5000 l_limit=0 h_limit=0 h_table=0
[ 0.831793] cpu cpu0: failed to find power_model node
[ 0.832783] sdhci: Secure Digital Host Controller Interface driver
[ 0.832804] sdhci: Copyright(c) Pierre Ossman
[ 0.832820] Synopsys Designware Multimedia Card Interface Driver
[ 0.833741] dwmmc_rockchip fe2b0000.dwmmc: IDMAC supports 32-bit address mode.
[ 0.833876] dwmmc_rockchip fe2b0000.dwmmc: Using internal DMA controller.
[ 0.833897] dwmmc_rockchip fe2b0000.dwmmc: Version ID is 270a
[ 0.833954] dwmmc_rockchip fe2b0000.dwmmc: DW MMC controller at irq 44,32 bit host data width,256 deep fifo
[ 0.834063] dwmmc_rockchip fe2b0000.dwmmc: Linked as a consumer to regulator.6
[ 0.834196] dwmmc_rockchip fe2b0000.dwmmc: Got CD GPIO
[ 0.846303] mmc_host mmc1: Bus speed (slot 0) = 375000Hz (slot req 400000Hz, actual 375000HZ div = 0)
[ 0.859762] dwmmc_rockchip fe2c0000.dwmmc: IDMAC supports 32-bit address mode.
[ 0.859871] dwmmc_rockchip fe2c0000.dwmmc: Using internal DMA controller.
[ 0.859893] dwmmc_rockchip fe2c0000.dwmmc: Version ID is 270a
[ 0.859943] dwmmc_rockchip fe2c0000.dwmmc: DW MMC controller at irq 45,32 bit host data width,256 deep fifo
[ 0.860035] dwmmc_rockchip fe2c0000.dwmmc: Linked as a consumer to regulator.6
[ 0.860149] mmc_host mmc2: card is non-removable.
[ 0.873146] mmc_host mmc2: Bus speed (slot 0) = 375000Hz (slot req 400000Hz, actual 375000HZ div = 0)
[ 0.886038] sdhci-pltfm: SDHCI platform and OF driver helper
[ 0.887119] mmc0: Unknown controller version (5). You may experience problems.
[ 0.918308] mmc0: SDHCI controller on fe310000.sdhci [fe310000.sdhci] using ADMA
[ 0.919553] hidraw: raw HID events driver (C) Jiri Kosina
[ 0.919910] usbcore: registered new interface driver usbhid
[ 0.919928] usbhid: USB HID core driver
[ 0.920276] rockchip,bus bus-npu: Linked as a consumer to regulator.13
[ 0.920305] rockchip,bus bus-npu: Failed to get leakage
[ 0.920367] rockchip,bus bus-npu: pvtm = 88520, from nvmem
[ 0.920390] rockchip,bus bus-npu: pvtm-volt-sel=1
[ 0.920653] rockchip,bus bus-npu: avs=0
[ 0.922721] rockchip-saradc fe720000.saradc: Linked as a consumer to regulator.5
[ 0.923288] optee: probing for conduit method from DT.
[ 0.923325] optee: revision 3.13 (4167319d)
[ 0.923659] optee: initialized driver
[ 0.923683] rksfc_base v1.1 2016-01-08
[ 0.924266] rksfc fe300000.sfc: rksfc_probe clk rate = 99000000
[ 0.924354] rkflash_dev_init enter
[ 0.924378] sfc nor id: 0 0 0
[ 0.924392] rkflash[1] is invalid
[ 0.924394] rkflash_dev_init enter
[ 0.924415] sfc_nand id: 0 0 0
[ 0.924420] rkflash[2] is invalid
[ 0.928555] rockchip-pinctrl pinctrl: pin gpio1-4 already requested by fe680000.serial; cannot claim for fe460000.spdif
[ 0.928590] rockchip-pinctrl pinctrl: pin-36 (fe460000.spdif) status -22
[ 0.928601] rockchip-pinctrl pinctrl: could not request pin 36 (gpio1-4) from group spdifm0-tx on device rockchip-pinctrl
[ 0.928610] rockchip-spdif fe460000.spdif: Error applying setting, reverse things back
[ 0.928633] rockchip-spdif: probe of fe460000.spdif failed with error -22
[ 0.929998] ipip: IPv4 and MPLS over IPv4 tunneling driver
[ 0.930446] Initializing XFRM netlink socket
[ 0.930479] IPsec XFRM device driver
[ 0.930906] NET: Registered protocol family 10
[ 0.931857] Segment Routing with IPv6
[ 0.932351] NET: Registered protocol family 17
[ 0.932383] NET: Registered protocol family 15
[ 0.932517] [BT_RFKILL]: Enter rfkill_rk_init
[ 0.932535] [WLAN_RFKILL]: Enter rfkill_wlan_init
[ 0.932960] [WLAN_RFKILL]: Enter rfkill_wlan_probe
[ 0.933003] [WLAN_RFKILL]: can't find rockchip,grf property
[ 0.933020] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi_chip_type = ap6210
[ 0.933032] [WLAN_RFKILL]: wlan_platdata_parse_dt: enable wifi power control.
[ 0.933043] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi power controled by gpio.
[ 0.933078] [WLAN_RFKILL]: wlan_platdata_parse_dt: WIFI,vbat_gpio = 73, flags = 0.
[ 0.933107] [WLAN_RFKILL]: wlan_platdata_parse_dt: The ref_wifi_clk not found !
[ 0.933120] [WLAN_RFKILL]: rfkill_wlan_probe: init gpio
[ 0.933136] [WLAN_RFKILL]: Failed to get rkwifi_wlan_vbat gpio.
[ 0.933164] wlan-platdata: probe of wireless-wlan failed with error -1
[ 0.933732] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: uart_rts_gpios = 77.
[ 0.933769] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,reset_gpio = 79.
[ 0.933792] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,wake_gpio = 81.
[ 0.933813] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,wake_host_irq = 80.
[ 0.933885] [BT_RFKILL]: Request irq for bt wakeup host
[ 0.933981] [BT_RFKILL]: ** disable irq
[ 0.934116] [BT_RFKILL]: bt_default device registered.
[ 0.934344] NET: Registered protocol family 36
[ 0.934380] Key type dns_resolver registered
[ 0.934602] flash vendor_init_thread!
[ 0.934620] flash vendor storage:20170308 ret = -1
[ 0.935843] Loading compiled-in X.509 certificates
[ 0.936035] Key type ._fscrypt registered
[ 0.936051] Key type .fscrypt registered
[ 0.936065] Key type fscrypt-provisioning registered
[ 0.936733] pstore: Using compression: deflate
[ 0.954598] mmc0: new HS200 MMC card at address 0001
[ 0.955608] mmcblk0: mmc0:0001 DG4064 58.2 GiB
[ 0.956323] mmcblk0boot0: mmc0:0001 DG4064 partition 1 4.00 MiB
[ 0.956875] mmcblk0boot1: mmc0:0001 DG4064 partition 2 4.00 MiB
[ 0.957091] mmcblk0rpmb: mmc0:0001 DG4064 partition 3 16.0 MiB, chardev (240:0)
[ 0.960165] mmcblk0: p1 p2 p3 p4 p5 p6 p7
[ 0.961774] asoc-simple-card hdmi-sound: i2s-hifi <-> fe400000.i2s mapping ok
[ 0.966598] rockchip-pm rockchip-suspend: not set pwm-regulator-config
[ 0.967273] ALSA device list:
[ 0.967289] #0: hdmi-sound
[ 0.970873] VFS: Mounted root (squashfs filesystem) readonly on device 179:6.
[ 0.971861] devtmpfs: mounted
[ 0.974316] Freeing unused kernel memory: 1344K
[ 0.996031] Run /sbin/init as init process
[ 1.066828] vendor storage:20190527 ret = 0
[ 1.203605] init: Console is alive
[ 1.203743] init: - watchdog -
[ 1.226039] rk-pcie 3c0800000.pcie: PCIe Linking... LTSSM is 0x0
[ 1.497617] mmc2: queuing unknown CIS tuple 0x01 (3 bytes)
[ 1.505480] mmc2: queuing unknown CIS tuple 0x1a (5 bytes)
[ 1.508891] mmc2: queuing unknown CIS tuple 0x1b (8 bytes)
[ 1.509584] mmc2: queuing unknown CIS tuple 0x14 (0 bytes)
[ 1.510664] mmc_host mmc2: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0)
[ 1.511686] mmc2: queuing unknown CIS tuple 0x80 (1 bytes)
[ 1.511748] mmc2: queuing unknown CIS tuple 0x81 (1 bytes)
[ 1.511810] mmc2: queuing unknown CIS tuple 0x82 (1 bytes)
[ 1.511849] mmc2: new high speed SDIO card at address 0001
[ 2.239401] rk-pcie 3c0800000.pcie: PCIe Linking... LTSSM is 0x0
[ 2.718638] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 2.752783] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 2.759181] init: - preinit -
[ 3.252702] rk-pcie 3c0800000.pcie: PCIe Linking... LTSSM is 0x0
[ 3.989316] yzhnag..8521 fiber workaround init for eth0,macbase=0xffffffc1f8ff0000
[ 3.991319] yzhang..8521 init call out...
[ 3.992443] YT8521 Ethernet stmmac-1:00: attached PHY driver [YT8521 Ethernet] (mii_bus:phy_addr=stmmac-1:00, irq=POLL)
[ 4.003437] dwmac4: Master AXI performs any burst length
[ 4.003531] rk_gmac-dwmac fe010000.ethernet eth0: No Safety Features support found
[ 4.003592] rk_gmac-dwmac fe010000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
[ 4.004278] rk_gmac-dwmac fe010000.ethernet eth0: registered PTP clock
[ 4.005120] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 4.266130] rk-pcie 3c0800000.pcie: PCIe Linking... LTSSM is 0x0
[ 5.279481] rk-pcie 3c0800000.pcie: PCIe Linking... LTSSM is 0x1
[ 6.228705] mount_root: loading kmods from internal overlay
[ 6.268437] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[ 6.271491] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[ 6.292680] rk-pcie 3c0800000.pcie: PCIe Linking... LTSSM is 0x0
[ 6.633682] F2FS-fs (loop0): Mounted with checkpoint version = 5ccce2da
[ 6.633844] block: attempting to load /tmp/f2fs_cfg/upper/etc/config/fstab
[ 6.635871] block: extroot: not configured
[ 6.723285] F2FS-fs (loop0): Mounted with checkpoint version = 5ccce2dd
[ 6.723717] mount_root: loading kmods from internal overlay
[ 6.757629] kmodloader: loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/*
[ 6.759841] kmodloader: done loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/*
[ 6.943719] block: attempting to load /tmp/f2fs_cfg/upper/etc/config/fstab
[ 6.944212] block: extroot: not configured
[ 6.966656] mount_root: switching to f2fs overlay
[ 6.969500] urandom-seed: Seeding with /etc/urandom.seed
[ 7.043156] procd: - early -
[ 7.043223] procd: - watchdog -
[ 7.309371] rk-pcie 3c0800000.pcie: PCIe Linking... LTSSM is 0x0
[ 7.691704] procd: - watchdog -
[ 7.691944] procd: - ubus -
[ 8.097990] procd: - init -
Please press Enter to activate this console.
[ 8.319368] rk-pcie 3c0800000.pcie: PCIe Linking... LTSSM is 0x0
[ 8.763192] kmodloader: loading kernel modules from /etc/modules.d/*
[ 8.818412] tun: Universal TUN/TAP device driver, 1.6
[ 8.833844] l2tp_core: L2TP core driver, V2.0
[ 8.837548] l2tp_netlink: L2TP netlink interface
[ 9.002388] Bluetooth: Core ver 2.22
[ 9.002506] NET: Registered protocol family 31
[ 9.002522] Bluetooth: HCI device and connection manager initialized
[ 9.002543] Bluetooth: HCI socket layer initialized
[ 9.002557] Bluetooth: L2CAP socket layer initialized
[ 9.002590] Bluetooth: SCO socket layer initialized
[ 9.008994] usbcore: registered new interface driver btusb
[ 9.009475] compat: loading out-of-tree module taints kernel.
[ 9.010377] Loading modules backported from Linux version v5.15.8-0-g43e577d7a2cb
[ 9.010421] Backport generated by backports.git v5.15.8-1-0-g83f664bb
[ 9.013377] Bluetooth: HCI UART driver ver 2.3
[ 9.013423] Bluetooth: HCI UART protocol H4 registered
[ 9.013429] Bluetooth: HCI UART protocol BCSP registered
[ 9.013435] Bluetooth: HCI UART protocol ATH3K registered
[ 9.013716] Bluetooth: HCI UART protocol Intel registered
[ 9.013729] Bluetooth: HCI UART protocol AG6XX registered
[ 9.013740] Bluetooth: HCI UART protocol Marvell registered
[ 9.015272] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 9.015315] Bluetooth: HIDP socket layer initialized
[ 9.075647] BUG: spinlock bad magic on CPU#0, kmodloader/612
[ 9.075696] lock: 0xffffff80090798c0, .magic: 00000000, .owner: <none>/-1, .owner_cpu: 0
[ 9.075706] CPU: 0 PID: 612 Comm: kmodloader Tainted: G O 4.19.232-photonicat #1
[ 9.075711] Hardware name: Rockchip RK3568 photonicat Linux Board (DT)
[ 9.075718] Call trace:
[ 9.075731] dump_backtrace+0x0/0x188
[ 9.075738] show_stack+0x24/0x30
[ 9.075750] dump_stack+0x8c/0xb4
[ 9.075779] spin_bug+0x88/0xa8
[ 9.075796] do_raw_spin_lock+0x3c/0xd8
[ 9.075812] _raw_spin_lock_irqsave+0x28/0x38
[ 9.075827] atomic_notifier_chain_register+0x28/0x5c
[ 9.075861] nf_conntrack_register_notifier+0x2c/0x38 [nf_conntrack]
[ 9.075878] ctnetlink_net_init+0x34/0x94 [nf_conntrack_netlink]
[ 9.075891] ops_init+0xe8/0x10c
[ 9.075900] register_pernet_operations+0xf4/0x1a0
[ 9.075910] register_pernet_subsys+0x3c/0x5c
[ 9.075924] ctnetlink_init+0x90/0x1000 [nf_conntrack_netlink]
[ 9.075935] do_one_initcall+0xa0/0x1c0
[ 9.075946] do_init_module+0x54/0x1d8
[ 9.075957] load_module+0x1ac8/0x1c14
[ 9.075964] __se_sys_init_module+0x1e0/0x210
[ 9.075971] __arm64_sys_init_module+0x24/0x30
[ 9.075978] el0_svc_common.constprop.0+0xe8/0x168
[ 9.075985] el0_svc_handler+0x70/0x8c
[ 9.075991] el0_svc+0x8/0xc
[ 9.097901] Bluetooth: RFCOMM socket layer initialized
[ 9.098014] Bluetooth: RFCOMM ver 1.11
[ 9.108581] usbcore: registered new interface driver usbserial_generic
[ 9.108676] usbserial: USB Serial support registered for generic
[ 9.145551] xt_time: kernel timezone is -0000
[ 9.153246] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 9.155584] usbcore: registered new interface driver cdc_ncm
[ 9.197467] usbcore: registered new interface driver huawei_cdc_ncm
[ 9.240099] PPP generic driver version 2.4.2
[ 9.241275] PPP MPPE Compression module registered
[ 9.242264] NET: Registered protocol family 24
[ 9.244295] usbcore: registered new interface driver qmi_wwan
[ 9.245664] usbcore: registered new interface driver sierra
[ 9.245725] usbserial: USB Serial support registered for Sierra USB modem
[ 9.247180] usbcore: registered new interface driver sierra_net
[ 9.270486] Bridge firewalling registered
[ 9.271677] usbcore: registered new interface driver cdc_mbim
[ 9.273692] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[ 9.276891] usbcore: registered new interface driver option
[ 9.276950] usbserial: USB Serial support registered for GSM modem (1-port)
[ 9.280990] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 9.332678] rk-pcie 3c0800000.pcie: PCIe Linking... LTSSM is 0x0
[ 9.487395] ath10k_sdio mmc2:0001:1: qca9377 hw1.1 sdio target 0x05020001 chip_id 0x00000000 sub 0000:0000
[ 9.487437] ath10k_sdio mmc2:0001:1: kconfig debug 0 debugfs 0 tracing 0 dfs 1 testmode 0
[ 9.489029] ath10k_sdio mmc2:0001:1: firmware ver WLAN.TF.1.1.1-00061-QCATFSWPZ-1 api 5 features ignore-otp crc32 7746e551
[ 9.721813] ath10k_sdio mmc2:0001:1: failed to fetch board data for bus=sdio,vendor=0271,device=0701,subsystem-vendor=0000,subsystem-device=0000 from ath10k/QCA9377/hw1.0/board-2.bin
[ 9.750334] ath10k_sdio mmc2:0001:1: board_file api 1 bmi_id N/A crc32 544289f7
[ 10.349383] rk-pcie 3c0800000.pcie: PCIe Linking... LTSSM is 0x0
[ 10.504018] zram0: detected capacity change from 0 to 2010120192
[ 10.543726] Adding 1963004k swap on /dev/zram0. Priority:-2 extents:1 across:1963004k SSDsc
[ 11.359360] rk-pcie 3c0800000.pcie: PCIe Link Fail
[ 11.359400] rk-pcie 3c0800000.pcie: failed to initialize host
[ 13.291302] ath10k_sdio mmc2:0001:1: htt-ver 3.32 wmi-op 4 htt-op 3 cal otp max-sta 32 raw 0 hwcrypto 1
[ 13.306122] mmc_host mmc2: Bus speed (slot 0) = 375000Hz (slot req 400000Hz, actual 375000HZ div = 0)
[ 13.896964] mmc2: queuing unknown CIS tuple 0x01 (3 bytes)
[ 13.904773] mmc2: queuing unknown CIS tuple 0x1a (5 bytes)
[ 13.908245] mmc2: queuing unknown CIS tuple 0x1b (8 bytes)
[ 13.908967] mmc2: queuing unknown CIS tuple 0x14 (0 bytes)
[ 13.910114] mmc_host mmc2: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0)
[ 13.910221] ath: EEPROM regdomain sanitized
[ 13.910235] ath: EEPROM regdomain: 0x64
[ 13.910242] ath: EEPROM indicates we should expect a direct regpair map
[ 13.910255] ath: Country alpha2 being used: 00
[ 13.910263] ath: Regpair used: 0x64
[ 14.132660] yzhnag..8521 fiber workaround init for eth1,macbase=0xffffffc1f8418000
[ 14.134678] yzhang..8521 init call out...
[ 14.135808] YT8521 Ethernet stmmac-0:00: attached PHY driver [YT8521 Ethernet] (mii_bus:phy_addr=stmmac-0:00, irq=POLL)
[ 14.146907] dwmac4: Master AXI performs any burst length
[ 14.146951] rk_gmac-dwmac fe2a0000.ethernet eth1: No Safety Features support found
[ 14.146975] rk_gmac-dwmac fe2a0000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported
[ 14.147244] rk_gmac-dwmac fe2a0000.ethernet eth1: registered PTP clock
[ 14.147911] br-lan: port 1(eth1) entered blocking state
[ 14.147931] br-lan: port 1(eth1) entered disabled state
[ 14.148244] device eth1 entered promiscuous mode
[ 14.149747] br-lan: port 1(eth1) entered blocking state
[ 14.149782] br-lan: port 1(eth1) entered forwarding state
[ 14.149876] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 14.287993] yzhang..8521 init call out...
[ 14.289142] YT8521 Ethernet stmmac-1:00: attached PHY driver [YT8521 Ethernet] (mii_bus:phy_addr=stmmac-1:00, irq=POLL)
[ 14.331676] dwmac4: Master AXI performs any burst length
[ 14.331726] rk_gmac-dwmac fe010000.ethernet eth0: No Safety Features support found
[ 14.331748] rk_gmac-dwmac fe010000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
[ 14.331986] rk_gmac-dwmac fe010000.ethernet eth0: registered PTP clock
[ 14.332291] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 15.078865] br-lan: port 1(eth1) entered disabled state
[ 15.433244] ath: EEPROM regdomain: 0x8348
[ 15.433274] ath: EEPROM indicates we should expect a country code
[ 15.433282] ath: doing EEPROM country->regdmn map search
[ 15.433288] ath: country maps to regdmn code: 0x3a
[ 15.433294] ath: Country alpha2 being used: US
[ 15.433299] ath: Regpair used: 0x3a
[ 15.433307] ath: regdomain 0x8348 dynamically updated by user
[ 16.439879] netlink: 'iw': attribute type 302 has an invalid length.
[ 20.322532] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 20.328811] br-lan: port 2(wlan0) entered blocking state
[ 20.328878] br-lan: port 2(wlan0) entered disabled state
[ 20.329626] device wlan0 entered promiscuous mode
[ 20.427292] 8021q: 802.1Q VLAN Support v1.8
[ 20.596646] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 20.596870] br-lan: port 2(wlan0) entered blocking state
[ 20.596896] br-lan: port 2(wlan0) entered forwarding state
[ 20.597198] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 21.297914] of_dma_request_slave_channel: dma-names property of node '/serial@fe680000' missing or empty
[ 21.297951] ttyS4 - failed to request DMA, use interrupt mode
[ 32.052808] pcie30_3v3: disabling
[ 46.655865] fast-classifier (PBR safe v2.1.4a): starting up
[ 46.656044] fast-classifier: registered
BusyBox v1.33.1 (2022-09-05 03:34:23 UTC) built-in shell (ash)
| |.-----.-----.-----.| | | |.----.| |_
| - _ | -| | | _ |
|___ |||||___||| |_|
|| W I R E L E S S F R E E D O M
OpenWrt 21.02, r3749-3401a701a
root@photonicat-openwrt:/#
root@photonicat-openwrt:/# `
